En este post te mostraré cómo forzar la salida HDMI en la Raspberry Pi, pues en ocasiones la Pi no envía señal HDMI a la pantalla o monitor, y solo sucede en estos casos. Es decir, te mostraré cómo solucionar el problema de que la Raspberry no envía señal.

A mí me pasó que en mi monitor funcionaba bien, pero en una pantalla de TV que tengo, no. Así que investigando encontré cómo hacer que la Raspberry Pi envíe señal HDMI.

Nota: obviamente esto funcionará si la Pi está funcionando normalmente, es decir, que tenga el sistema instalado y que esté comprobado que funciona y envía señal. Esto más que nada es para cuando el problema es el monitor o pantalla.

Configurando boot/config.txt

Te recomiendo crear un respaldo del archivo antes de modificarlo.

Todo lo que necesitamos configurar está en /boot/config.txt. Puedes usar el editor nano o vim, incluso puedes conectar la SD a Windows y el mismo detectará la partición.

Lo que tenemos que cambiar es lo siguiente, pero además te recomiendo que mires el archivo que dejo más adelante:

  • hdmi_group=2
  • hdmi_mode=4
  • hdmi_force_hotplug=1

Por cierto, hdmi_safe debe estar comentado. Es decir, tener un # al inicio. Solo como referencia, aquí dejo mi config.txt.

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
hdmi_group=2
hdmi_mode=4

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d

De este modo la Raspberry va a funcionar en todas o al menos la mayoría de pantallas, manteniendo la compatibilidad con las que anteriormente ya funcionaba. No olvides reiniciar el sistema.

Con esto me refiero a que en mi caso lo configuré así para que fuera compatible con una TV, pero al conectarla a mi monitor seguía funcionando sin problemas. Lo único que cambió un poco fue la resolución pero eso no fue molesto pues al final la iba a usar para convertirla en consola.

Archivo config.txt original

Por cierto, en caso de que configures algo y después no funcione, te recomiendo conectarte por SSH y restablecer el archivo original. Por si no lo tienes, aquí lo dejo:

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment this if your display has a black border of unused pixels visible
# and your display can output without overscan
#disable_overscan=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2

[all]
#dtoverlay=vc4-fkms-v3d

Solo recuerda que deberías tomarlo para guiarte, pues puede que en tu caso el original sea diferente debido a una actualización o diferencia de software.

Si el post ha sido de tu agrado te invito a que me sigas para saber cuando haya escrito un nuevo post, haya actualizado algún sistema o publicado un nuevo software. Facebook | X | Instagram | Telegram | También estoy a tus órdenes para cualquier contratación en mi página de contacto